Wifi qcom ac mikrotik manual. 11ax AP (not my case).

Wifi qcom ac mikrotik manual. This is now supported with the wifi-qcom-ac drivers.


Wifi qcom ac mikrotik manual Announcements; RouterOS; Beginner Basics; there are a few manual steps when replacing wireless package with wifi-qcom-ac (read WiFi manual to prepare in advance) I watched videos and changed drivers with wifi-qcom-ac and reconfigure capsman. The official Wifi documentation from Mikrotik has a sample under https: "Passing datapaths "MAIN/GUEST" from the start of the example to "wifi-qcom-ac" CAP would be misconfiguration, 3. If wireless The existing "wifiwave2" package has been divided into distinct packages: "wifi-qcom" and "wifi-qcom-ac", and the necessary utilities for WiFi management are now included in the RouterOS Is there anyone who solved this issue in a better way than manual configuring this? And does anybody have some information on whether MT's developers would implement the https://help. 13rc4 (2023-Dec-12 15:16): Replacing the the 'wireless' with the 'wifi-qcom-ac' + usage of CAPsMAN (where are also devices connected to with MIPS CPU) seems a little bit tricky to me. 7. Top . So it seems that the problem actually starts on cAP ax This is now supported with the wifi-qcom-ac drivers. you have to manually add the wifi interface(s) to the bridge on every CAP with the appropriate pvid. Top. it works-- the cap running qcom-ac driver receives it on the bridge interface and a PVID is Unfortunately all devices with decent switch chip and without bridge HW offload are ac devices (hAP ac2, hAP ac3, Audience, cAP ac, etc. What does this even mean? RouterOS version 7. 11ax (aka Wi-Fi 6) devices (using the wifi-qcom Therefore the current solution involves some manual configuration on the CAP's itself. Here we will assume that ether1 is used as a WAN port and ether2-ether5 are used as LAN ports. Client Device: Raspberry Pi Lora for IoT device management. If wireless package is missing, fetch it from extras archive (available on mikrotik download page), drop it on hAP ac lite and reboot. But when I look at competitors PDF manuals - then I have the feeling that Mikrotik ROS We all know MikroTik WiFi has been behind other vendors. Long story short, wifiwave2 is dead, all hail wifi-qcom[-ac]. holvoetn Forum Guru Posts: 6409 Joined: Tue Apr 13, 2021 12:14 am Overview. More info: Therefore the current solution involves some manual configuration on the CAP's itself. Forum Guru. 3 stable but not with the standard wireless drivers, more with the wifi-qcom-ac driver. Hi,I have L009UiGS-RM as CAPSMAN Controller and some cAP ac with wifi-qcom-ac package. I switched over Mikrotik, any chance to add this feature to the new wifi-qcom-ac drivers? On the side note: 7. Loading Spaces 3. ) running wifi-qcom-ac kind of makes me mad because MT isn't touching wifi-qcom-ac any more (it seems that they are waiting for everybody remembering these devices to die due to suffocation while holding our breathe wireless > wifi-qcom-ac > wifi-qcom In terms of modern feature compatibility, wireless < wifi-qcom-ac < wifi-qcom (and it's the same in terms of price, at least with the used market in mind) I have a network of devices, all ARM, all with the wifi-qcom-ac driver. 11ax AP (not my case). Weitere Informationen finden Sie oben unter Konformitätserklärung / Cet appareil MikroTik respecte les limites maximales de puissance de transmission WLAN conformément 1. Even with proper AP configuration with manual bridge / vlan configuration. 4 on my CAP XL AC device. 3 Apple Hardware tested: - MacBook Air M1 If you want new wireless drivers (cAP AC is compatible), first remove wireless package, then install wifi-qcom-ac package (it's in extra packages) but be sure to fully understand the consequences ! cAP AC is a device with only 16Mb storage and ROS >= 7. This kind of user support and freedom is what makes MikroTik special! 3. Download Extra packages. Go to MikroTik Software page. Option #1, using Winbox. Unfortunately I later found out, Firstly, hats off to MikroTik for allowing using the Qualcom 802. Instead, AP accepts configuration for the We had to roll back the AC access points - removing the wifi-qcom-ac package and revert back to wireless package. 15. 13, is a RouterOS menu for managing Wi-Fi 5 wave2 and newer WiFi interfaces. !) wifi - split existing "wifiwave2" package into separate packages "wifi-qcom", "wifi-qcom-ac", and include required utilities for WiFi management into bundle; !) wireless - separate "wireless" package from bundle and build as a standalone package; 3. The feature set of legacy is way more rich, wifi offers fewer features but much better performance. 14RC1 with new wifi-qcom-ac to have roaming working. 13 пакет Wifiwave2 разделился и появилось 2 новых пакета wifi-qcom-ac для поддержки AC и wifi-qcom для поддержки AX Method 1 - MikroTik Software page. it works-- the cap running qcom-ac driver receives it on the bridge interface and a PVID is set "As of today, wifi-qcom/AX driver is equipped with only Home-AP quickSet preset. I do have 3 cap AC in my home wifi, recently updated to 7. Эти пакеты представляют собой отдельные поколения WiFi оборудования MikroTik. In terms of stability and convenience, wireless > wifi-qcom-ac > wifi-qcom In terms of modern feature compatibility, wireless < wifi-qcom-ac < wifi-qcom (and it's the same in terms of price, at least with the used market in mind)I have a network of devices, all ARM, all with the wifi-qcom-ac driver. php?f=13&t=166330 But heres the catch: Before the change to wifi-qcom-ac the channels were 20MHz wide (as per configuration) and did not overlap. 11ax or 802. The feature Many of configurations, created by those profiles, are already possible, but they require painful manual config. Followed MikroTik documentation within their Wiki, and even adjusted the CAPsMAN provisioning to be "create enabled" instead of "create dynamic enabled". The main router acts as a router, firewall and a CapsMan Controller. Last edited by mkx on Fri Dec 29, 2023 3:47 pm, edited 3 Mikrotik help wifi capsman Should be When "pushing" new config, or re-provisioning the CAP running qcom-ac driver, the WLAN interfaces change and increment; breaking the bridge and vlan assignment for the WLAN SSID's. After uninstalling wireless The documentation says that the VLAN configuration at the moment still requires manual configuration for each AP managed by CAPsMAN, no matter 802. Пакет wifi-qcom и wifi-qcom-ac это представитель нового 3. it works-- the cap running qcom-ac driver receives it on the bridge interface and a PVID is set mkx wrote: ↑ Fri Dec 29, 2023 2:41 pm There are two distinct wireless driver packs: legacy "wireless" which supports older wirrless chipsets up to and including ac. The qcom-ac was not stable in a production environment. Unfortunately all devices with decent switch chip and without bridge HW offload are ac devices (hAP ac2, hAP ac3, Audience, cAP ac, etc. Firstly, hats off to MikroTik for allowing using the Qualcom 802. 15beta8 [mips] 3 x Mikrotik cAP AC (RBcAPGi-5acD2nD) using RouterOS 7. Any general troubleshooting advice? 2. 13 you need to have two packages installed: routeros (the main package) and wireless (your device doesn't qualify for the new wifi-qcom-ac package). 49. *) wifi-qcom - updated regulatory info for Ukraine, Australia and United States; *) wifi-qcom-ac - allow use of channel 144 under "Japan" regulatory domain; *) wifi-qcom-ac - fix possible conflict between radio and USB initialization on hAP ac2; *) wifi-qcom-ac - improved CPU load balancing and system stability; see the sample configuration for wifi-qcom-ac here and in particular the note: "Passing datapaths "MAIN/GUEST" from the start of the example to "wifi-qcom-ac" CAP would be misconfiguration, make sure to use datapath without "vlan-id" specified to such devices". I'm having a tough time getting a working configuration with the new wifi-qcom-ac package. That's a completely different driver and hardware. So for now the driver does not have support for setting up a datapath/bridge over the CAPsMANv2 with configured vlans for virtual ap's. But the "lost feature" -> "VLAN configuration in the wireless settings (Per-interface VLANs I configured wifi, enabled WAP2-EAP, all working. If you want new wireless drivers (cAP AC is compatible), first remove wireless package, then install wifi-qcom-ac package (it's in extra packages) but be sure to fully understand the consequences ! cAP AC is a device with only 16Mb storage and ROS >= 7. Quote #2; Wed Dec 18, 2024 8:16 pm. This kind of user support and freedom is what makes MikroTik special! When "pushing" new config, or re-provisioning the CAP running qcom-ac driver, the WLAN interfaces change and increment; breaking the bridge and vlan assignment for the WLAN SSID's. Old driver "wireless" is removed, and another one "wifi-qcom" is only for 802. CAP Configuration. MikroTik hAP ac lite RB952Ui-5ac2nD Access Point for Wi-Fi. The documentation says that the VLAN configuration at the moment still requires manual configuration for each AP managed by CAPsMAN, no matter 802. !) wifi - split existing "wifiwave2" package into separate packages "wifi-qcom", "wifi-qcom-ac", and include required utilities for WiFi management into bundle; !) wireless - separate "wireless" package from bundle and build as a standalone package; mkx wrote: ↑ Fri Dec 29, 2023 2:41 pm There are two distinct wireless driver packs: legacy "wireless" which supports older wirrless chipsets up to and including ac. 12 left around 700kB of storage unused. Devices with compatible radios also require either the 'wifi-qcom-ac' driver package (for 802. 14. Each one is on ROS7 7. 4 and use the wifi-qcom-ac module, my esp32 devices and xiaomi cleaning robot (all using 2. Currently and trying to do the same on 7. Who needs a manager which is not capable of managing its caps? Idiotic. 13beta3 (2023-Nov-24 13:52): As I already know the vlan configuration of cAP-AC's is a bit nasty with the new wifi-qcom-ac package. 11 k/r/v. 13. 13rc4 (2023-Dec-12 15:16): "As of today, wifi-qcom/AX driver is equipped with only Home-AP quickSet preset. 13 + wifi-qcom-ac might be a bit too tight, depending on what you use that device for. After upgraded to 7. For more detailed information see Declaration of Conformity above / Dieses MikroTik-Gerät erfüllt die maximalen WLAN Sendeleistung Grenzwerte gemäß ETSI-Bestimmungen. Devices would not stay connected. 11r/k/v. What's new in 7. Building 3 - Other Home: MikroTik SXTsq Lite2 antenna (PtMP link). Дата выхода: 7 февраля 2024. 13 to allocate different vlans to clients? My setup worked very well on V6 with capsman. 11ac (different drivers used for each one): section CAPsMAN - CAP VLAN configuration example describes basic CAPsmAN config with VLAN in datapath, and CAP config for both drivers: Linked Applications. The official Wifi documentation from Mikrotik has a sample under https: "Passing datapaths "MAIN/GUEST" from the start of the example to "wifi-qcom-ac" CAP would be misconfiguration, 2. Use wifi-qcom for new devices, wifi-qcom-ac for ARM-powered older devices. 3. If I change the wifi module to 'wireless', everything works fine. However, the wifi interface shows "failed to set country" if either wifi1 or wifi2 is enabled. 11ac chipsets) or the 'wifi-qcom' driver package for 802. !) wifi - split existing "wifiwave2" package into separate packages "wifi-qcom", "wifi-qcom-ac", and include required utilities for WiFi management into bundle; !) wireless - separate "wireless" package from bundle and build as a standalone package; - if you want wave2 wifi (ac2 can do it): add wifi-qcom-ac package For both cases: be aware storage space might become a problem later on. VLANs with wifi-qcom-ac and capsman makes capsman look like a complete useless dumb manager. x with the old wirelesss package, but ofc roaming experience was quite poor. 12. vlan-id" in your wifi configuration on CAPsMAN, but this is not supported with CAPs running wifi-qcom-ac. I updated the mikrotik hap ac lite software to v. The existing "wifiwave2" package has been divided into distinct packages: "wifi-qcom" and "wifi-qcom-ac", and the necessary utilities for WiFi management are now included in the RouterOS bundle. Even with proper AP configuration with manual bridge / Overview. [Dynamic their documentation is not that complete. As I already know the vlan configuration of cAP-AC's is a bit nasty with the new wifi-qcom-ac package. More info: wireless > wifi-qcom-ac > wifi-qcom In terms of modern feature compatibility, wireless < wifi-qcom-ac < wifi-qcom (and it's the same in terms of price, at least with the used market in mind) I have a network of devices, all ARM, all with the wifi-qcom-ac driver. Even with proper AP configuration with manual bridge / Upload matching version of qcom-ac package; Reboot Upload script to configure access point (which is frowned upon) Reset configuration and run script; Change password and identity; Alternatively carry out manual reconfiguration of default CAPS configuration which is fiddly to say the least. 16, wifi-qcom-ac, VLAN, CAPSMAN, mDNS and AP ethernet ports. The secondary router acts as a CapsMan2 Controller, for tests and migration from Router 6 to RouterOS 7 and wireless to wifi-qcom-ac. Before this update I has no stability issues on the 7. I have an Mikrotik infrastructure with a main router RB1100AHx4 (RouterOS 6. (the main package) and wireless (your device doesn't qualify for the new wifi-qcom-ac package). !) wifi - split existing "wifiwave2" package into separate packages "wifi-qcom", "wifi-qcom-ac", and include required utilities for WiFi management into bundle; !) wireless - separate "wireless" package from bundle and build as a standalone package; When "pushing" new config, or re-provisioning the CAP running qcom-ac driver, the WLAN interfaces change and increment; breaking the bridge and vlan assignment for the WLAN SSID's. You can skip Step1 if you are already using the default configuration on your router. The one thing that does not work is dynamic assignment of VLAN ids to my wifi clients. wireless > wifi-qcom-ac > wifi-qcom In terms of modern feature compatibility, wireless < wifi-qcom-ac < wifi-qcom (and it's the same in terms of price, at least with the used market in mind) I have a network of devices, all ARM, all with the wifi-qcom-ac driver. If you either reset it to CAPS Mode through the reset button or the menu option it will give you the same state (and doesn't require any manual adjustments). I can't get any client devices to associate with the access point after swapping wireless packages. I finally got to the point to open another thread on this I recently often thought about. My issue is, trying to connect to an existing WiFi gives me the message, "not running". The same configuration tree is shared with wave2/wifi capsman. we're still software limited by Mikrotik with them using the newer qualcom Devices would not stay connected. 13beta3 (2023-Nov-24 13:52): Moving from /interface/wireless ("wireless") to /interface/wifi ("wifi-qcom" and "wifi-qcom-ac") may cause service interrruption. For really old ones, use the 'wireless' package. it works-- the cap running qcom-ac driver receives it on the bridge interface and a PVID is On a lower level, the WiFi CAPsMAN can specify a VLAN ID as a datapath parameter; this also only works with the ax devices whereas for the ac devices running wifi-qcom-ac, you have to set the VLAN tag for a wifi interface manually, by means of Firstly, hats off to MikroTik for allowing using the Qualcom 802. For ac devices, using the wifi-qcom-ac driver this is indeed the case. And the latter will help supporting clients to select the best radio. 13), an hEX secondary router (RouterOS 7. 11ac other 802. com/docs/display/ROS/WiFi#WiFi-CAPusing%22wifi-qcom-ac%22package: In particular the roaming standards 802. I'm As I already know the vlan configuration of cAP-AC 's is a bit nasty with the new wifi-qcom-ac package. Before you can start configuring CAPsMAN, you must configure your selected CAPsMAN device as a router. 11ac) and 60GHz wireless interfaces. What is shown is a config if you want to do it manually from scratch. I'm an old Mikrotik user since the RT532 model. 13, it This portal lists hardware manuals for MikroTik products. RouterOS and "wifi-qcom-ac" packages alongside each other now fit into 16MB flash memory. But yet, when I was "testing" the Datapath setting in CAPsMan for sending VLAN-ID. In your case, only capsman for legacy (remote) radios will be using wireless configuration subtree. 13 wireless package split question. Manual configuration required. 17rc3). 11ac (different drivers used for each one): section CAPsMAN - CAP VLAN configuration example describes basic CAPsmAN config with VLAN in datapath, and CAP config for both drivers: 3. Things like ports, slots, buttons and mounting options are described here. In RB5009 (since it's not wireless device) none of wifi-qcom packages is necessary, wifi capsman is part of basic package. 7. The 'WiFi' configuration menu, introduced in RouterOS 7. Starting with 7. There are two capsmans, legacy to control CAPs which run legacy wireless drivers, and wave2/wifi capsman to control wifi-running CAPs. Konfiguracja tego sterownika znacząco różni się od poprzednich wersji. " Which is fine, I have been trying to do that. This doesn't mix. ) running wifi-qcom-ac kind of makes me mad because MT isn't touching wifi-qcom-ac any more (it seems that they are waiting for everybody remembering these devices to die due to suffocation while holding our breathe Therefore the current solution involves some manual configuration on the CAP's itself. MikroTik hAP ac lite RB952Ui-5ac2nD Access Point for the VLANs. W nowej odsłonie opiera się ona na profilach, co jest dobrze znane z konfiguracji Capsmana. Hi, great job. I prefer to go VLAN all the 3. Thanks for the help. Therefore the current solution involves some manual configuration on the CAP's itself. That's why there are also responses saying it works perfectly on iOS 18. infabo. I use FreeRadius on a pfsense, and this part seems And the new wifi (wifi-qcom and wifi-qcom-ac) which supports newer wireless chipsets from ac and upwards. You really want to read the above link carefully, there are some manual steps to take. I have a few wAP ac AP's. Select the appropriate RouterOS version for your device. New CAPsMAN is in the 'routeros' system package, old CAPsMAN is I have updated the wireless packages to use wifi-qcom and wifi-qcom-ac, and gone about setting up the configs as per the Mikrotik docs: https: In most cases, there is no reason to perform manual provisioning once you already have CAP interfaces running. The model page to download offers wrong files, this is what caused my difficulties. we're still software limited by Mikrotik with them using the newer qualcom drivers. 13beta has been released on the "v7 testing" channel! Before an upgrade: 1) Remember to make backup/export files before an upgrade and save them on another stor I have an iPhone 12 with iOS 18 that connects to wAPacR with wifi-qcom-ac (and defaults with DFS disabled) I prefer a good old searchable manual anytime over whatever video which usually is a waste of time for the most part (to me). infabo Forum Guru Posts: 1236 Joined: Thu Nov 12 2. On my hAP ac^2 I'm currently using the wireless package. The official Wifi documentation from Mikrotik has a sample under https: "Passing datapaths "MAIN/GUEST" from the start of the example to "wifi-qcom-ac" CAP would be misconfiguration, Therefore the current solution involves some manual configuration on the CAP's itself. then better wording in manuals and advertisements would be good in case it is planned "feature" My experience so far is that each new Mikrotik device is better (but backward compatible). And the new wifi (wifi-qcom and wifi-qcom-ac) which supports newer wireless chipsets from ac and upwards. MikroTik Community discussions. 1 x Mikrotik RB5009UPr+s+IN Router using RouterOS 7. 13rc4 (2023-Dec-12 15:16): Moving from /interface/wireless ("wireless") to /interface/wifi ("wifi-qcom" and "wifi-qcom-ac") may cause service interrruption. My current setup includes, cAP ac can be run with wifi-qcom-ac driver and does support the latest bennefits. Could this possibly mean that there is support for the cAP AC? And because you didn't mention it, many people here believed your issue was was with an AX AP (wifi-qcom driver). 11ax CAPs and wifi-qcom-ac on the 802. I have a system with several cAP-ACs running ROS 7. Moving from /interface/wireless ("wireless") to /interface/wifi ("wifi-qcom" and "wifi-qcom-ac") may cause service interrruption. There was excitement around the release of Moving from /interface/wireless ("wireless") to /interface/wifi ("wifi-qcom" and "wifi-qcom-ac") may cause service interrruption. 13rc4 (2023-Dec-12 15:16): В RouterOS 7. 15beta8 + wireless-qcom-ac [arm] VLANs And this works just fine ever since conception of wifiwave2 family of drivers (which current wifi, wifi-qcom and wifi-qcom-ac are comming from). 13 this changed drivers are now packaged in wifi-qcom and wifi-qcom-ac packages. More info: 2. 13beta1 with legacy wireless left around 400kB of storage unused. Sub-menu: /interface wireless cap When an AP is configured to be controlled by CAPsMAN, configuration of the managed wireless interfaces on the AP is ignored (exceptions: antenna-gain,antenna-mode). *) wifi - use correct CAP identity for interface name provisioning after it has been changed by remote-cap/set-identity; *) wifi-qcom - enable display of regulatory information on L11,L22 devices; *) wifi-qcom - fixed new connections, when maximum supported number of MAC addresses behind connected station-bridges is reached; Wifi interface on L009 is only supported by wifi-qcom driver and has to be configured via wifi configuration subtree (in CLI that's /interface/wifi). Up until and including 7. Since the upgrade the channels seem to Since 7. I'm running an RB4011 in combination with 2x cAP XL ac and 1x wAP ac. After uninstalling wireless Overview. 13beta3 (2023-Nov-24 13:52):. 11ac CAPs. W wersji RouterOS 7. 4. And also works for legacy wireless driver, so it's the recommended way of doing it unless one has advanced needs which can't be solved by using this way of configuring things. 15beta8 [arm64] 2 x Mikrotik CRS109-8G-1S-2HnD Router/Switch/APs running RouterOS 7. 1 there was indeed wifiwave2 optional package, with 7. 2 (it seems to be the best in v7 series so far) on cAP ac and replace wireless package with wifi-qcom-ac. kovacspro just joined Posts: 17 Joined: Wed Jun 14, 2023 6:57 pm. However, the Audience is an AC device with a wifi-qcom-ac driver. New wifi driver (wifi-qcom and wifi-qcom-ac, but the same was already in original wifiwave2 driver) can't tag/untag frames. I'm also experiencing this same issue. 2. Mikrotik Capsman i wifi-qcom. Point-to-MultiPoint Link: RouterOS version 7. you (edit: meant to refer to OP here, but it's probably the same problem in both cases) are using "datapath. 13rc4 (2023-Dec-12 15:16): wireless > wifi-qcom-ac > wifi-qcom In terms of modern feature compatibility, wireless < wifi-qcom-ac < wifi-qcom (and it's the same in terms of price, at least with the used market in mind) I have a network of devices, all ARM, all with the wifi-qcom-ac driver. - if you want wave2 wifi (ac2 can do it): add wifi-qcom-ac package For both cases: be aware storage space might become a problem later on. What does this even mean? Инструкция по настройке CAPsMAN для пакетов: wirelles, wifi-qcom и wifi-qcom-ac. It's in the new WiFi manual, section "Replacing 'wireless' package" under "Lost features". 13 and I lost the WIFI configuration, as everything has changed. !) wifi - split existing "wifiwave2" package into separate packages "wifi-qcom", "wifi-qcom-ac", and include required utilities for WiFi management into bundle; !) wireless - separate "wireless" package from bundle and build as a standalone package; 2. 11ax and newer chipsets. If you have a mixed bag of devices, some 802. Devices with compatible radios also Utilities and drivers for managing WiFi (up to 802. 11ac requires 80MHz channels, made up of 4 x 20MHz channels For any given 80 MHz chunk, there are 4 possible assignments, depending on which one you make the control channel We had to roll back the AC access points - removing the wifi-qcom-ac package and revert back to wireless package. We've upgraded their IPQ-4019 devices to newer wifi-qcom-ac driver package, but not without issue. 13/7. Wireless or wifi-qcom are located in Extra packages zip file. Post wireless > wifi-qcom-ac > wifi-qcom In terms of modern feature compatibility, wireless < wifi-qcom-ac < wifi-qcom (and it's the same in terms of price, at least with the used market in mind) I have a network of devices, all ARM, all with the wifi-qcom-ac driver. but my download speed did not above 400-410mbps again. Mikrotik has two (actually three wifi-qcom-ac - works only with ac devices and enables some additional features compared to wireless wifi-qcom - works with ax devices corrected the situation. 13 Mikrotik wprowadził nowy sterownik do obsługi interfejsów WiFi – wifi-qcom. . Another option (possibly better) is to install ROS 7. 11ac ath10k WiFi driver (wifi-qcom-ac); it has a lot of latency and fairness benefits on top of Wave 2 support. If you are looking for configuration - the This repo is to hold my configuration files for a complex home network based on Mikrotik networ To discuss this please join us here : https://forum. When "pushing" new config, or re-provisioning the CAP running qcom-ac driver, the WLAN interfaces change and increment; breaking the bridge and vlan assignment Does anybody know if radius authentication with an external radius servers works with the new drivers wifi-qcom-ac 7. 11ac (different drivers used for each one): section CAPsMAN - CAP VLAN configuration example describes basic CAPsmAN config with VLAN in datapath, and CAP config for both drivers: Hi,I have L009UiGS-RM as CAPSMAN Controller and some cAP ac with wifi-qcom-ac package. Posts: 1442 Joined: Thu Nov 12 wireless > wifi-qcom-ac > wifi-qcom In terms of modern feature compatibility, wireless < wifi-qcom-ac < wifi-qcom (and it's the same in terms of price, at least with the used market in mind) I have a network of devices, all ARM, all with the wifi-qcom-ac driver. 2x Mikrotik wAP AC (RBwAPG-5HacD2HnD) ROS 7. When "pushing" new config, or re-provisioning the CAP running qcom-ac driver, the WLAN interfaces change and increment; breaking the bridge and vlan assignment for the WLAN SSID' s. 13 and struggling to make it I have updated the RouterOS and the wifi-qcom-ac package to version 7. The upgrade to the wifi-qcom-ac driver is hughly recommended, performance is better and it has support for 802. 100% agree. mikrotik. 802. The official Wifi documentation from Mikrotik has a sample under https: "Passing datapaths "MAIN/GUEST" from the start of the example to "wifi-qcom-ac" CAP would be misconfiguration, Yes, only one should be active and you need wifi-qcom for running local wifi interface, so basically on L009 you should forget about wireless package. And then for all of a sudden, learning the hard way, you have to use "create enabled" instead of "create dynamic enabled" so wifi interfaces are not renamed on config Overview. In this case you'll have to configure CAPsMAN on RB4011 under /interface/wifi (all configuration subtree, new you (edit: meant to refer to OP here, but it's probably the same problem in both cases) are using "datapath. The ax devices do support VLAN assigning through CAPsMAN. 13beta3 (2023-Nov-24 13:52): If you want new wireless drivers (cAP AC is compatible), first remove wireless package, then install wifi-qcom-ac package (it's in extra packages) but be sure to fully understand the consequences ! cAP AC is a device with only 16Mb storage and ROS >= 7. 13 (2023-Dec-14 09:24): Connect to Mikrotik wifi network and connect to CAP AC with Winbox(this is easiest with a laptop). Step #1, setup router wifi-qcom - improved memory allocating process; wifi-qcom - improved regulatory compliance for L11, L22 devices; wifi-qcom - improved system stability for L11, L22 devices; MikroTik RouterOS 7. On the cAP's i replaced the wireless package with the wifi-qcom-ac package. 13 (2023-Dec-14 09:24): MikroTik SXT 2 antenna (PtMP link between Main Home and Other Home). Before the manual upgrade, I should have seen which The configuration of the devices using the wifi-qcom-ac package in case of CAPsMAN - CAP VLAN configuration is different from devices using the wifi-qcom package, make sure you are following the documentation CAPs that support wifi-qcom-ac package section not the one before it which is for the 802. 13rc has been released on the "v7 testing" channel! Before an upgrade: 1) Remember to make backup/export files before an upgrade and save them on another storag Moving from /interface/wireless ("wireless") to /interface/wifi ("wifi-qcom" and "wifi-qcom-ac") may cause service interrruption. com/viewtopic. The 'WiFi' configuration menu, introduced in RouterOS 7. The official Wifi documentation from Mikrotik has a sample under https: "Passing datapaths "MAIN/GUEST" from the start of the example to "wifi-qcom-ac" CAP would be misconfiguration, Mikrotik, any chance to add this feature to the new wifi-qcom-ac drivers? On the side note: 7. What does this even mean? And you have to do manual VLAN filtering on ac devices (using the wifi-qcom-ac driver), as it doesn't support this through the current driver. This package is bundled into RouterOS for versions up to 7. 4G wifi) are being disconnected once connected to routers. Select the appropriate Architecture of your device (device architecture can be found in System → Resource). 11ax, then you need wifi-qcom on the CAPsMAN, wifi-qcom on the 802. I have been hoping for this for a long time . MikroTik Support Posts: 26168 Joined: Fri May 28, 2004 9:04 am Location: Riga, Latvia. "As of today, wifi-qcom/AX driver is equipped with only Home-AP quickSet preset. 2 "wifi-qcom-ac" driver, because of new features, better performance and new "WiFi" menu support, as docs says in Compatibility section. njxve wykqx iqtx knkmaf atkq sipp qvn thz pvvkz ecujwp